FAQ
Autodimmers
2) Dimmer LEDs can affect only when fading occurs directly or fading, and then the eye is almost not noticeable.
2) If you are in Kiev, we drive up to (pre-contract) we will deliver free next model DM-2.3A, DM-2.3L, DM-2.3N, DM-2.3V
1) Check the insertion of the device according to the scheme in the instructions, and visually verify that you have connected
2) Check if the power is fed to the device (great help multimeter)
3) Do not confuse recheck if the power (+ and -)
4) Check the system voltage (should be between 12-14,5 V)
5) If all of the above does not work, find EXPLANATORY (required) electrician and give him instructions, machines, and can ... money, maybe help
6) call us :-(
Wiring dimmer is in the instruction manual, and usually it is very simple, based on the basic knowledge of electronics and knowledge of any notation able to connect it. Also see below are two basic types of connection
Wiring dimmer aveopodobnyh cars (minus the body of the car is under the screw)
Wiring dimmer lanosopodobnyh cars (all three wires in one connector)
If nothing happens, then there call us by phones specified in the header
One touch turn module
How a function works "thank you"
1) Extenders turns LC-1.6 programmed as follows:
- correctly connect the device according to the scheme;
- turn on the power to the device, from this moment begins the countdown (10 seconds), after which, entering the programming mode will be impossible;
- Include a right turn onto two blinks, then turn left turn onto two blinks. ;
- The device will confirm entry in programming mode by blinking right turn and then a left turn;
- Programming number of blinks turns elongational: Turn right turn down to the number of flashes and turn it off.
2) LC-1.4H modules and LC-1.4L programmed as follows:
- correctly connect the device according to the scheme;
- turn on the power to the unit and within 5 seconds after the force the 3 flashing left turn, left turn switch off, turn on the 3 flashing right turn, stop turn right - the device will blink twice alarms in acknowledgment of entering the programming mode;
- turn left turn and count the number of the desired extension turns, turn off left turn;
- turn right turn and count the number of blinks desired function "thank you" to turn off the turn, the device flashes twice in acknowledgment exit programming.
2) Check if the power is fed to the device (excellent helps tester)
3) Do not confuse recheck whether power polarity (+ and -)
4) Check the system voltage (should be between 12-14,5 V)
5) If all of the above does not work, find EXPLANATORY (required) electrician and give him instructions, machines, and can ... money, maybe help
6) call us :-(
2) Recheck the insertion device of diagram in, and visually verify that you have connected (Did you accidentally hooked it vice versa)
3) Recheck the correct connection of the orange and blue wires
4) If all of the above does not work, find EXPLANATORY (required) electrician and give him instructions, machines, and can ... money, maybe help
5) call us :-( And if suddenly burned, then send to us for repair.
1) For power applications (all versions LC-1.4 и LC-1.8)
2) For low-voltage circuits (LC-1.6)
3) Polarity alarm management, while reversing
- controlled positive polarity (LC-1.4H и LC-1.8)
- controlled negative polarity (LC-1.4L)
4) In a work schedule
- from the nominal relay LC-1.4H, LC-1.4L (clicks when working corners, or alarm)
- Interval time LC-1.6, LC-1.8 (major peaks in turns during operation, or alarm)
In the module version LC-1.4H it responds to the positive polarity (+),
In the module version LC-1.4L it responds only to the negative polarity (-)
In the module version LC-1.6 it responds to the positive polarity (+)
User connection One-touch turn signal module, go to the instruction manual, in the liner. If you can not find the fate that we will put into the device, or we put her provtykal you see below.
Instruction One-touch turn signal module LC-1.4H
Instruction One-touch turn signal module LC-1.4L
Instruction One-touch turn signal module LC-1.6
What would just pick up the device production CAR CHIPS on your car, or find a scheme, it is sufficient to just use a special filter and select your make and model of car, seen in the video how to do it. If not your circuit, then ask us a question here
либо дорабатываете родное - необходимо допаять всего один резистор
RPC
Connect the red wire "Dad" on 12 volts, the black wire "dad" to - 12 volts, the yellow wire "dad" briefly touch 12 volt trigger relay (must clearly be an audible click). At the same time on the yellow wire "mother" should appear 12 Volt
User manual Relay pause RPC-3.1
Should be connected according to the diagram, the place where to place the device near the stalk windshield, pay special attention to the connection in cars like VAZ, in the presence of thermal bimetal relay, our device will not work
Also there is a switch on the rear wiper pause, wiring diagrams for them are below
User manual Relay pause RPC-2.1 on the car Logan MCV, Duster, Sandero, etc.
User manual Relay pause RPC-2.1 on VAZ with rear wiper(2104, 2107)
Instructions on the new modifications and wiring to them are below
User manual Relay rear wiper pause RPC-2.2
MCDRL
- Connect the negative to the vehicle body;
- +12 V to output device "+12"
- Output device "Lamp" on one of the conclusions of the halogen lamp, connect the second terminal to the vehicle body;
- Connect LED bundled according to the scheme - + pitenie directly to the car, and - on the conclusion "OUT-";
- +12 V output on the "IGN +" and pay attention to the LED display:
- smoothly switched through a preset time - the device is turned on and operating normally;
- flashes when the - device software disabled;
If the device when executing the above instructions are not enabled, then write us
- MCDRLmanagement LED lights with total current potrebelnie 3Amper to have control of the tail lights, dim light, handbrake, turn on and off smoothly DRL, have a mode of programming time, inclusion and decrease the brightness level;
- SmartDRL connected in parallel standard wiring, run halogen bulbs with a maximum capacity of up to 10 amps are programmable on-time after starting the engine, the power level of the glow lamps turn on and off smoothly DRL, shutdown management of tail lights, or handbrake (you can not connect, the device will work), and software unit can be turned on or off at a time when it is not needed (nonvolatile memory)
- EasyDRLthe cheapest version of the device, works with halogen main beam lamps connected in series with the circuit does not have programming modes, the light is turned on immediately after turning the ignition on the power level of 42%, the lamp shuts management parking lights or handbrake (when connected appropriate conclusions, if not connected, the device will work, but will not be controlled by them)
- LiteDRLintermediate between SmartDRL and EasyDRL, designed to work with halogen bulbs main beam with two channels (only for positive polarity) lamps beam headlights (can be run with one channel) turns on the light when the ignition without time delay to the level of 30% of the power has control of the tail lights and brake (when connected appropriate conclusions, if not connected, the device will work, but will not be controlled by them), is not programmed
User manual Module MCDRL-3.0 all cars (controls only positive polarity), it works only with LEDs!
User manual Module LightDRL all cars (controls only positive polarity) works only with halogen lamps
User manual Module EasyDRL all cars (controls only positive polarity) works only with halogen lamps
User manual Module SmartDRL (Nordic light) all cars (controls only positive polarity) works only withhalogen bulbs beam
Should be connected according to the scheme, the place where to place the device itself is not critical, most importantly, to connect it to the scheme.
Delivery, payment, shipping, warranty and map
We are located at the following adress:
Ukraine, city Kyiv Peremogy avenue 123 (m. Zhitomirska) phone 066-699-07-07 Sergey
Политика возврата
Возврат устройств на наш адрес подлежит предварительному согласованию и возможен в течении 14 дней с момента покупки. Согласование производится с менеджером, может изначально обсуждаться по телефону, но обязательно должено быть продублировано по электронной почте. Возврат устройств, которые подверглись инсталляции не рассматривается. Отправка товара к нам наложенным платежом не рассматривается.
Возврат денежных средств на карту, или расчётный счёт осуществляется после подтверждения по электронной почте. Возврат денежных средств перечисляется на реквизиты покупателя данного товара. В письме необходимо указать фамилию, имя, отчество покупателя, реквизиты. Если у покупателя нет собственных реквизитов на возврат средств, и он хочет воспользоваться посторонними реквизитами, необходимо в письме указывать фамилию, имя, отчество покупателя с реквизитами того человека, на кого будут переведены денежные средства. Возврат денежных средств может длиться от 1 до 10 дней.
- We guarantee device requirements specifications subject to the consumer ekspulatatsii conditions.
-The warranty period is 12 months from the date of installation for the operation, but not more than 18 months from the date of shipment to the buyer.
- Manufactured free repairing device if during the warranty period the consumer will be found any discrepancy device specifications on the manufacturer's fault.
By law, the warranty becomes void in the following cases:
- damaged safety signs manufacturer or company-seller: stickers, stickers, holograms, seals etc;
- Products have been repaired by unauthorized persons in violation of the manufacturer and safety standards;
- defects caused by changes due to the use of goods for not conforming to the scope of the product specified in the instruction manual;
- the product is damaged or out of order in connection with the violation of the rules and conditions of installation, connection, adaptation to local tech. conditions of the buyer, use, storage and transport;
- equipment damaged by natural disasters, fires, floods, earthquakes, domestic factors and other situations beyond the control of Seller;
- product has expressed mechanical and / or electrical damage resulting from any action by the buyer or third parties;
- arose damage caused by ingestion of foreign objects products, substances, liquids, insects or animals;
- service representative was seen using contingency modes or parameters of the equipment or its components (frequency, voltage, etc.);
Доставка по странам СНГ осуществляется ТОЛЬКО Почтой Украины
которая взаимодействует с государственной почтой страны получателя
сроки доставки варьируются в пределах от 7 до 14 дней (иногда бывают задержки, связанные с работой почты ). Отправка товара осуществляется ТОЛЬКО по 100% предоплате товара
В ТЕЧЕНИИ 3-Х РАБОЧИХ ДНЕЙ С МОМЕНТА ОПЛАТЫ!!!
Если у Вас есть какие то сомнения, или нет доверия к нам, почитайте отзывы о нас в интернете или спросите уже у тех, кто купил наши устройства, они Вам с радостью помогут и подскажут.
Стоимость доставки одной единицы товара производства "Автофишки"
согласно таблицы
| Вес товара (грамм) | Стоимость доставки (USD) |
|---|---|
| 1-49 | 6 |
| 50-250 | 8 |
| 251-500 | 10 |
| 501-1000 | 21 |
| 1001-1500 | 25 |
| 1501-2000 | 30 |
| 2001-5000 | 40 |
Устройства с большими габаритами оплачиваются по отдельному тарифу
Оплата услуг связанных с перевозкой и доставкой товаров, а так же затрат связанного возврата належенного платежа осуществляется получателем.
После отправки товара, мы уведомляем покупателя несколькими методами:
- в ответ на письмо заказ высылаем трек-номер посылки;
- отправляем смс сообщение с трек-номером на указанный номер при регистрации;
- регистрируем трек-номер посылки на сайте Post-Tracker.ru и при изменении статуса Вашей посылки на указанный email при регистрации приходит письмо со статусом посылки.
Заранее благодарны за понимание.
Отследить движение товара, возможно на этом же сайте по этой ссылке
FAQ
FAQ